Linux version 6.6.7 (olek@mocarz) (i686-buildroot-linux-uclibc-gcc.br_real (Buildroot 2022.05-1002-g1500b7d5c8) 12.1.0, GNU ld (GNU Binutils) 2.38) #34 Wed Dec 13 19:25:54 CET 2023
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
BIOS-provided physical RAM map:
BIOS-e820: [mem 0x0000000000000000-0x000000000009f7ff] usable
BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved
BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
BIOS-e820: [mem 0x0000000000100000-0x000000001bedffff] usable
BIOS-e820: [mem 0x000000001bee0000-0x000000001bee2fff] ACPI NVS
BIOS-e820: [mem 0x000000001bee3000-0x000000001beeffff] ACPI data
BIOS-e820: [mem 0x000000001bef0000-0x000000001befffff] reserved
BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
BIOS-e820: [mem 0x00000000ffff0000-0x00000000ffffffff] reserved
Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
APIC: Static calls initialized
SMBIOS 2.5 present.
DMI: IGEL Technology GmbH M310C/VX855 , BIOS 6.00 PG 07/20/2011
tsc: Fast TSC calibration using PIT
tsc: Detected 997.511 MHz processor
e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
e820: remove [mem 0x000a0000-0x000fffff] usable
last_pfn = 0x1bee0 max_arch_pfn = 0x100000
MTRR map: 9 entries (7 fixed + 2 variable
x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT  
found SMP MP-table at [mem 0x000f3820-0x000f382f]
initial memory mapped: [mem 0x00000000-0x01ffffff]
ACPI: Early table checksum verification disabled
ACPI: RSDP 0x00000000000F7840 000014 (v00 VX855 )
ACPI: RSDT 0x000000001BEE3000 000038 (v01 VX855  AWRDACPI 42302E31 AWRD 00000000)
ACPI: FACP 0x000000001BEE3080 000074 (v01 VX855  AWRDACPI 42302E31 AWRD 00000000)
ACPI: DSDT 0x000000001BEE3100 00377C (v01 VX855  AWRDACPI 00001000 MSFT 03000000)
ACPI: FACS 0x000000001BEE0000 000040
ACPI: HPET 0x000000001BEE6900 000038 (v01 VX855  AWRDACPI 42302E31 AWRD 00000098)
ACPI: WDRT 0x000000001BEE6940 000047 (v01 VX855  AWRDACPI 42302E31 AWRD 00000000)
ACPI: MCFG 0x000000001BEE69C0 00003C (v01 VX855  AWRDACPI 42302E31 AWRD 00000000)
ACPI: APIC 0x000000001BEE6880 00005A (v01 VX855  AWRDACPI 42302E31 AWRD 00000000)
ACPI: Reserving FACP table memory at [mem 0x1bee3080-0x1bee30f3]
ACPI: Reserving DSDT table memory at [mem 0x1bee3100-0x1bee687b]
ACPI: Reserving FACS table memory at [mem 0x1bee0000-0x1bee003f]
ACPI: Reserving HPET table memory at [mem 0x1bee6900-0x1bee6937]
ACPI: Reserving WDRT table memory at [mem 0x1bee6940-0x1bee6986]
ACPI: Reserving MCFG table memory at [mem 0x1bee69c0-0x1bee69fb]
ACPI: Reserving APIC table memory at [mem 0x1bee6880-0x1bee68d9]
0MB HIGHMEM available.
446MB LOWMEM available.
mapped low ram: 0 - 1bee0000
low ram: 0 - 1bee0000
Zone ranges:
DMA      [mem 0x0000000000001000-0x0000000000ffffff]
Normal   [mem 0x0000000001000000-0x000000001bedffff]
HighMem  empty
Movable zone start for each node
Early memory node ranges
node   0: [mem 0x0000000000001000-0x000000000009efff]
node   0: [mem 0x0000000000100000-0x000000001bedffff]
Initmem setup node 0 [mem 0x0000000000001000-0x000000001bedffff]
On node 0, zone DMA: 1 pages in unavailable ranges
On node 0, zone DMA: 97 pages in unavailable ranges
ACPI: PM-Timer IO Port: 0x408
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x11068201 base: 0xfe800000
[mem 0x1bf00000-0xdfffffff] available for PCI devices
clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0 
Kernel command line: panic=30 printk.devkmsg=on tsc=unstable     
tsc: Marking TSC unstable due to boot parameter
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
Built 1 zonelists, mobility grouping on.  Total pages: 113408
mem auto-init: stack:off, heap alloc:off, heap free:off
Initializing HighMem for node 0 (00000000:00000000)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
Memory: 427840K/457208K available (2391K kernel code, 3413K rwdata, 668K rodata, 17028K init, 1144K bss, 29368K reserved, 0K cma-reserved, 0K highmem)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS: 2304, nr_irqs: 48, preallocated irqs: 16
Console: colour VGA+ 80x25
printk: console [tty0] enabled
ACPI: Core revision 20230628
clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
APIC: Switch to symmetric I/O mode setup
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
Calibrating delay loop (skipped), value calculated using timer frequency.. 1995.02 BogoMIPS (lpj=9975110)
process: using mwait in idle threads
Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
CPU: Centaur VIA Nano U3500@1000MHz (family: 0x6, model: 0xf, stepping: 0xa)
Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
Spectre V2 : Kernel not compiled with retpoline
Spectre V2 : Vulnerable
Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
Speculative Store Bypass: Vulnerable
L1TF: Kernel not compiled for PAE. No mitigation for L1TF
MDS: Vulnerable: Clear CPU buffers attempted, no microcode
MMIO Stale Data: Unknown: No mitigations
x86/fpu: x87 FPU will use FXSAVE
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
Performance Events: 
core: Welcome to zhaoxin pmu!
core: Version check pass!
no PMU driver, software events only.
signal: max sigframe size: 1440
NMI watchdog: Perf NMI watchdog permanently disabled
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
futex hash table entries: 256 (order: -1, 3072 bytes, linear)
NET: Registered PF_NETLINK/PF_ROUTE protocol family
thermal_sys: Registered thermal governor 'step_wise'
thermal_sys: Registered thermal governor 'user_space'
cpuidle: using governor ladder
cpuidle: using governor menu
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved as E820 entry
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
ACPI: Added _OSI(Module Device)
ACPI: Added _OSI(Processor Device)
ACPI: Added _OSI(3.0 _SCP Extensions)
ACPI: Added _OSI(Processor Aggregator Device)
ACPI: 1 ACPI AML tables successfully acquired and loaded
ACPI: _OSC evaluation for CPUs failed, trying _PDC
ACPI: Interpreter enabled
ACPI: PM: (supports S0 S5)
ACPI: Using IOAPIC for interrupt routing
PCI: Using host bridge windows from ACPI
PCI: Using E820 reservations for host bridge windows
ACPI: Enabled 8 GPEs in block 00 to 0F
ACPI: Enabled 2 GPEs in block 10 to 1F
ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig Segments HPX-Type3]
acpi PNP0A08:00: PCIe port services disabled
acpi PNP0A08:00: _OSC: platform retains control of PCIe features (AE_NOT_FOUND)
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000dffff window]
pci_bus 0000:00: root bus resource [mem 0x1bf00000-0xdfffffff window]
pci_bus 0000:00: root bus resource [mem 0xf0000000-0xfebfffff window]
pci_bus 0000:00: root bus resource [bus 00-ff]
pci 0000:00:00.0: [1106:0409] type 00 class 0x060000
pci 0000:00:00.1: [1106:1409] type 00 class 0x060000
pci 0000:00:00.2: [1106:2409] type 00 class 0x060000
pci 0000:00:00.3: [1106:3409] type 00 class 0x060000
pci 0000:00:00.4: [1106:4409] type 00 class 0x060000
pci 0000:00:00.5: [1106:5409] type 00 class 0x080020
pci 0000:00:00.6: [1106:6409] type 00 class 0x060000
pci 0000:00:00.7: [1106:7409] type 00 class 0x060000
pci 0000:00:01.0: [1106:5122] type 00 class 0x030000
pci 0000:00:01.0: reg 0x10: [mem 0xd8000000-0xdbffffff pref]
pci 0000:00:01.0: reg 0x14: [mem 0xde000000-0xdeffffff]
pci 0000:00:01.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
pci 0000:00:01.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
pci 0000:00:01.0: supports D1 D2
pci 0000:00:0f.0: [1106:c409] type 00 class 0x01018a
pci 0000:00:0f.0: reg 0x20: [io  0xff00-0xff0f]
pci 0000:00:0f.0: legacy IDE quirk: reg 0x10: [io  0x01f0-0x01f7]
pci 0000:00:0f.0: legacy IDE quirk: reg 0x14: [io  0x03f6]
pci 0000:00:0f.0: legacy IDE quirk: reg 0x18: [io  0x0170-0x0177]
pci 0000:00:0f.0: legacy IDE quirk: reg 0x1c: [io  0x0376]
pci 0000:00:10.0: [1106:3038] type 00 class 0x0c0300
pci 0000:00:10.0: reg 0x20: [io  0xfe00-0xfe1f]
pci 0000:00:10.0: supports D1 D2
pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:10.1: [1106:3038] type 00 class 0x0c0300
pci 0000:00:10.1: reg 0x20: [io  0xfd00-0xfd1f]
pci 0000:00:10.1: supports D1 D2
pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:10.2: [1106:3038] type 00 class 0x0c0300
pci 0000:00:10.2: reg 0x20: [io  0xfc00-0xfc1f]
pci 0000:00:10.2: supports D1 D2
pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:10.4: [1106:3104] type 00 class 0x0c0320
pci 0000:00:10.4: reg 0x10: [mem 0xdffff000-0xdffff0ff]
pci 0000:00:10.4: supports D1 D2
pci 0000:00:10.4: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:11.0: [1106:8409] type 00 class 0x060100
pci 0000:00:11.7: [1106:a353] type 00 class 0x060000
pci 0000:00:13.0: [1106:b353] type 01 class 0x060401
pci 0000:00:14.0: [1106:3288] type 00 class 0x040300
pci 0000:00:14.0: reg 0x10: [mem 0xdfff8000-0xdfffbfff 64bit]
pci 0000:00:14.0: PME# supported from D0 D3hot D3cold
pci_bus 0000:01: extended config space not accessible
pci 0000:01:03.0: [10ec:8167] type 00 class 0x020000
pci 0000:01:03.0: reg 0x10: [io  0xee00-0xeeff]
pci 0000:01:03.0: reg 0x14: [mem 0xdfeff000-0xdfeff0ff]
pci 0000:01:03.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
pci 0000:01:03.0: supports D1 D2
pci 0000:01:03.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:00:13.0: PCI bridge to [bus 01] (subtractive decode)
pci 0000:00:13.0:   bridge window [io  0xe000-0xefff]
pci 0000:00:13.0:   bridge window [mem 0xdfe00000-0xdfefffff]
pci 0000:00:13.0:   bridge window [mem 0xdfd00000-0xdfdfffff 64bit pref]
pci 0000:00:13.0:   bridge window [io  0x0000-0x0cf7 window] (subtractive decode)
pci 0000:00:13.0:   bridge window [io  0x0d00-0xffff window] (subtractive decode)
pci 0000:00:13.0:   bridge window [mem 0x000a0000-0x000dffff window] (subtractive decode)
pci 0000:00:13.0:   bridge window [mem 0x1bf00000-0xdfffffff window] (subtractive decode)
pci 0000:00:13.0:   bridge window [mem 0xf0000000-0xfebfffff window] (subtractive decode)
pci_bus 0000:00: on NUMA node 0
ACPI: PCI: Interrupt link LNKA configured for IRQ 11
ACPI: PCI: Interrupt link LNKB configured for IRQ 7
ACPI: PCI: Interrupt link LNKC configured for IRQ 5
ACPI: PCI: Interrupt link LNKD configured for IRQ 10
ACPI: PCI: Interrupt link LNKE configured for IRQ 0
ACPI: PCI: Interrupt link LNKE disabled
ACPI: PCI: Interrupt link LNKF configured for IRQ 0
ACPI: PCI: Interrupt link LNKF disabled
ACPI: PCI: Interrupt link LNK0 configured for IRQ 0
ACPI: PCI: Interrupt link LNK0 disabled
ACPI: PCI: Interrupt link LNK1 configured for IRQ 0
ACPI: PCI: Interrupt link LNK1 disabled
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 64 bytes
e820: reserve RAM buffer [mem 0x0009f800-0x0009ffff]
e820: reserve RAM buffer [mem 0x1bee0000-0x1bffffff]
hpet0: at MMIO 0xfe800000, IRQs 2, 8, 0
hpet0: 3 comparators, 32-bit 14.318180 MHz counter
clocksource: Switched to clocksource hpet
pnp: PnP ACPI init
system 00:00: [io  0x0400-0x047f] has been reserved
system 00:00: [io  0x0500-0x050f] has been reserved
system 00:01: [mem 0xfea00000-0xfea000ff] has been reserved
system 00:02: [io  0x04d0-0x04d1] has been reserved
system 00:06: [mem 0xe0000000-0xefffffff] has been reserved
system 00:07: [mem 0x000f0000-0x000fffff] could not be reserved
system 00:07: [mem 0xfe800000-0xfe8000ff] has been reserved
system 00:07: [mem 0xfea00000-0xfea000ff] has been reserved
system 00:07: [mem 0x1bee0000-0x1befffff] could not be reserved
system 00:07: [mem 0xffff0000-0xffffffff] has been reserved
system 00:07: [mem 0x00000000-0x0009ffff] could not be reserved
system 00:07: [mem 0x00100000-0x1bedffff] could not be reserved
system 00:07: [mem 0xfec00000-0xfec00fff] could not be reserved
system 00:07: [mem 0xfee00000-0xfee00fff] has been reserved
system 00:07: [mem 0xfff80000-0xfffeffff] has been reserved
pnp: PnP ACPI: found 8 devices
clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
NET: Registered PF_INET protocol family
IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear)
Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
TCP: Hash tables configured (established 4096 bind 4096)
UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
NET: Registered PF_UNIX/PF_LOCAL protocol family
pci 0000:01:03.0: BAR 6: assigned [mem 0xdfe00000-0xdfe1ffff pref]
pci 0000:00:13.0: PCI bridge to [bus 01]
pci 0000:00:13.0:   bridge window [io  0xe000-0xefff]
pci 0000:00:13.0:   bridge window [mem 0xdfe00000-0xdfefffff]
pci 0000:00:13.0:   bridge window [mem 0xdfd00000-0xdfdfffff 64bit pref]
pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000dffff window]
pci_bus 0000:00: resource 7 [mem 0x1bf00000-0xdfffffff window]
pci_bus 0000:00: resource 8 [mem 0xf0000000-0xfebfffff window]
pci_bus 0000:01: resource 0 [io  0xe000-0xefff]
pci_bus 0000:01: resource 1 [mem 0xdfe00000-0xdfefffff]
pci_bus 0000:01: resource 2 [mem 0xdfd00000-0xdfdfffff 64bit pref]
pci_bus 0000:01: resource 4 [io  0x0000-0x0cf7 window]
pci_bus 0000:01: resource 5 [io  0x0d00-0xffff window]
pci_bus 0000:01: resource 6 [mem 0x000a0000-0x000dffff window]
pci_bus 0000:01: resource 7 [mem 0x1bf00000-0xdfffffff window]
pci_bus 0000:01: resource 8 [mem 0xf0000000-0xfebfffff window]
pci 0000:00:13.0: disabling DAC on VIA PCI bridge
PCI: CLS 64 bytes, default 64
workingset: timestamp_bits=30 max_order=17 bucket_order=0
i8042: PNP: No PS/2 controller found.
i8042: Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
Freeing unused kernel image (initmem) memory: 17028K
Write protecting kernel text and read-only data: 3060k
Run /init as init process
with arguments:
/init
with environment:
HOME=/
TERM=linux
softdog: initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=1)
softdog:              soft_reboot_cmd=<not set> soft_active_on_boot=0
io scheduler mq-deadline registered
lp: driver loaded but no devices found
Non-volatile memory driver v1.3
ACPI: bus type USB registered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci-pci 0000:00:10.4: EHCI Host Controller
ehci-pci 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:10.4: debug port 1
ehci-pci 0000:00:10.4: irq 23, io mem 0xdffff000
ehci-pci 0000:00:10.4: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
w83627hf: w83627hf: Found W83697HF chip at 0x290
w83627hf w83627hf.656: hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
rtc_cmos 00:03: RTC can wake from S4
rtc_cmos 00:03: registered as rtc0
rtc_cmos 00:03: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
00:04: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
00:05: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
SCSI subsystem initialized
libata version 3.00 loaded.
pata_via 0000:00:0f.0: version 0.3.4
scsi host0: pata_via
scsi host1: pata_via
ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
ata2: DUMMY
usb 1-1: new high-speed USB device number 2 using ehci-pci
ata1.00: CFA:  512MB ATA Flash Disk, ADBA217G, max PIO4
ata1.00: 1000944 sectors, multi 0: LBA 
ata1.00: applying bridge limits
scsi 0:0:0:0: Direct-Access     ATA       512MB ATA Flash 217G PQ: 0 ANSI: 5
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 20, io port 0x0000fe00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 22, io port 0x0000fd00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 21, io port 0x0000fc00
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
sd 0:0:0:0: [sda] 1000944 512-byte logical blocks: (512 MB/489 MiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
mc: Linux media interface: v0.10
videodev: Linux video capture interface: v2.00
usb 1-1: Found UVC 1.00 device <unnamed> (046d:0825)
usb 1-3: new high-speed USB device number 3 using ehci-pci
EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
watchdog: watchdog0: nowayout prevents watchdog being stopped!
watchdog: watchdog0: watchdog did not stop!
usbcore: registered new interface driver uvcvideo
snd_hda_intel 0000:00:14.0: Force to non-snoop mode
snd_hda_intel 0000:00:14.0: CORB reset timeout#1, CORBRP = 0
r8169 0000:01:03.0 eth0: RTL8169sc/8110sc, 00:e0:c5:36:01:03, XID 180, IRQ 16
r8169 0000:01:03.0 eth0: jumbo features [frames: 7146 bytes, tx checksumming: ok]
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
ACPI: button: Power Button [PWRB]
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
ACPI: button: Sleep Button [SLPB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: button: Power Button [PWRF]
input: PC Speaker as /devices/platform/pcspkr/input/input3
Warning: Processor Platform Limit event detected, but not handled.
Consider compiling CPUfreq support into your kernel.
snd_hda_codec_generic hdaudioC0D0: autoconfig for Generic: line_outs=1 (0x1c/0x0/0x0/0x0/0x0) type:line
snd_hda_codec_generic hdaudioC0D0:    speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
snd_hda_codec_generic hdaudioC0D0:    hp_outs=0 (0x0/0x0/0x0/0x0/0x0)
snd_hda_codec_generic hdaudioC0D0:    mono: mono_out=0x0
snd_hda_codec_generic hdaudioC0D0:    inputs:
snd_hda_codec_generic hdaudioC0D0:      Mic=0x1a
EXT4-fs (sda1): mounted filesystem acdf47a1-df56-4215-b025-5d18ac8c8cf1 r/w with ordered data mode. Quota mode: disabled.
ext3 filesystem being mounted at /media/sda1 supports timestamps until 2038-01-19 (0x7fffffff)
usb 4-1: new full-speed USB device number 2 using uhci_hcd
random: crng init done
usb 1-6: new high-speed USB device number 5 using ehci-pci
usb 1-1: set resolution quirk: cval->res = 384
usbcore: registered new interface driver snd-usb-audio
hub 1-6:1.0: USB hub found
hub 1-6:1.0: 4 ports detected
usb 1-3: USB disconnect, device number 3
usb 1-6.4: new high-speed USB device number 6 using ehci-pci
usb 1-3: new high-speed USB device number 7 using ehci-pci
usb-storage 1-3:1.3: USB Mass Storage device detected
scsi host2: usb-storage 1-3:1.3
usb-storage 1-3:1.4: USB Mass Storage device detected
scsi host3: usb-storage 1-3:1.4
usbcore: registered new interface driver usb-storage
brint: port 1(eth0) entered blocking state
brint: port 1(eth0) entered disabled state
r8169 0000:01:03.0 eth0: entered allmulticast mode
r8169 0000:01:03.0 eth0: entered promiscuous mode
RTL8211B Gigabit Ethernet r8169-0-118:00: attached PHY driver (mii_bus:phy_addr=r8169-0-118:00, irq=MAC)
brint: port 1(eth0) entered blocking state
brint: port 1(eth0) entered forwarding state
r8169 0000:01:03.0 eth0: Link is Down
Bluetooth: Core ver 2.22
NET: Registered PF_BLUETOOTH protocol family
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
usbcore: registered new interface driver btusb
Bluetooth: hci0: CSR: Setting up dongle with HCI ver=6 rev=22bb
Bluetooth: hci0: LMP ver=6 subver=22bb
usb 1-6.4: reset high-speed USB device number 6 using ehci-pci
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
zd1211rw 1-6.4:1.0: phy0
usbcore: registered new interface driver zd1211rw
usbcore: registered new interface driver option
usbserial: USB Serial support registered for GSM modem (1-port)
option 1-3:1.0: GSM modem (1-port) converter detected
usb 1-3: GSM modem (1-port) converter now attached to ttyUSB0
option 1-3:1.1: GSM modem (1-port) converter detected
usb 1-3: GSM modem (1-port) converter now attached to ttyUSB1
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver cdc_ncm
usbcore: registered new interface driver cdc_wdm
huawei_cdc_ncm 1-3:1.2: MAC-Address: 0c:5b:8f:27:9a:64
huawei_cdc_ncm 1-3:1.2: setting rx_max = 16384
huawei_cdc_ncm 1-3:1.2: setting tx_max = 16384
huawei_cdc_ncm 1-3:1.2: NDP will be placed at end of frame for this device.
huawei_cdc_ncm 1-3:1.2: cdc-wdm0: USB WDM device
huawei_cdc_ncm 1-3:1.2 wwan0: register 'huawei_cdc_ncm' at usb-0000:00:10.4-3, Huawei CDC NCM device, 0c:5b:8f:27:9a:64
usbcore: registered new interface driver huawei_cdc_ncm
scsi 3:0:0:0: Direct-Access     HUAWEI   TF CARD Storage  2.31 PQ: 0 ANSI: 2
scsi 2:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
sd 3:0:0:0: [sdb] 124821504 512-byte logical blocks: (63.9 GB/59.5 GiB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 0f 00 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 3:0:0:0: [sdb] Attached SCSI removable disk
zd1211rw 1-6.4:1.0: firmware version 4725
zd1211rw 1-6.4:1.0: zd1211b chip 079b:0062 v4810 high 00-19-70 AL2230_RF pa0 g--NS
brint: port 1(eth0) entered disabled state
NET: Registered PF_PACKET protocol family
r8169 0000:01:03.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx
brint: port 1(eth0) entered blocking state
brint: port 1(eth0) entered forwarding state
brint: port 2(wlan0) entered blocking state
brint: port 2(wlan0) entered disabled state
zd1211rw 1-6.4:1.0 wlan0: entered allmulticast mode
zd1211rw 1-6.4:1.0 wlan0: entered promiscuous mode
brint: port 2(wlan0) entered blocking state
brint: port 2(wlan0) entered forwarding state
EXT4-fs (sdb1): mounted filesystem 31dc1c33-859e-439d-8314-ef4e4ff49799 r/w with ordered data mode. Quota mode: disabled.